User Tools

Site Tools


vhs_door_v3

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

vhs_door_v3 [2013/08/21 20:58]
tomkeddie
vhs_door_v3 [2014/06/17 16:13] (current)
tomkeddie
Line 11: Line 11:
 ==== Lock control and monitoring ==== ==== Lock control and monitoring ====
  
-The lock control and monitoring is done by an Arduino ​Diecimila ​with opto-isolated relays attached. ​ The schematic is shown below. ​  The lock handle is engaged by the existing bidirectional motor. ​ When not energized the relays pass control through to the motor from the keypad operated controller built in to the lock.  Each relay drives the motor in a different direction, there is no limit switch, the control is time based. ​ To allow someone to open or close the door, the lock is engaged for a period of time and then disengaged. ​ The relay optoisolators are connected to P2 and P3, not P1 and P2 as shown in the schematic.+The lock control and monitoring is done by an Arduino with opto-isolated relays attached. ​ The schematic is shown below. ​  The lock handle is engaged by the existing bidirectional motor. ​ When not energized the relays pass control through to the motor from the keypad operated controller built in to the lock.  Each relay drives the motor in a different direction, there is no limit switch, the control is time based. ​ To allow someone to open or close the door, the lock is engaged for a period of time and then disengaged. ​ The relay optoisolators are connected to P2 and P3, not P1 and P2 as shown in the schematic.
  
  {{ ::​2013-07-31_12.06.10.jpg?​200 |}}  {{ ::​2013-07-31_12.06.10.jpg?​200 |}}
  
 An additional optoisolator connected to P4 is used to provide feedback on the position of the door bolt, this is used for logging purposes only.  ​ An additional optoisolator connected to P4 is used to provide feedback on the position of the door bolt, this is used for logging purposes only.  ​
 +
 +==== Access Reader ====
 +
 +An Arduino is used to decode the wiegard protocol from the rfid reader and report it as a string to the RPi over a serial port.
  
 ==== RPi based control ==== ==== RPi based control ====
Line 21: Line 25:
 The access reader is connected the RPi via USB serial converter and is controlled/​monitoring via ascii strings over the serial port.  ​ The access reader is connected the RPi via USB serial converter and is controlled/​monitoring via ascii strings over the serial port.  ​
  
-===== USB Serial Converter ===== 
  
-The serial converter is an FTDI 4232H USB to quad serial converter[[http://​www.ftdichip.com/​Support/​Documents/​DataSheets/​Modules/​DS_FT4232H_Mini_Module.pdf|PDF]]. ​ It is wired for bus power as per the data sheet 
-<​code>​ 
-USB Bus-powered:​ 
-1) 
-Connect VBUS to VCC (CN3, pin 1 to CN3, pin 3). This connection takes the power from the USB bus (VBUS) and connects it to the voltage regulator input on the FT4232H Mini Module. The voltage regulator, in turn, provides V3V3, VPLL and VUSB power inputs to the FT4232H chip. 
-2) 
-Connect V3V3 to VIO (CN2, pins 1, 3 & 5 to CN2, pins 11 & 21 and CN3, pins 12 & 22). This connection provides the correct 3.3VDC operating voltage for VCCIO on the FT4232H chip.  
-</​code>​ 
vhs_door_v3.txt ยท Last modified: 2014/06/17 16:13 by tomkeddie